1. You will need an ATX PSU with at least 10 six-pin PCIe connectors. There are 3 six-pin PCIe connectors on each hashing board and all three need to be connected to the PSU for the hashing board to operate. Do not connect more than one PSU to the same hashing board. Bitmain recommends the APW3++ to power the V9.
2. Separate power supply to control board: there is one additional six-pin PCIe connector on the IO board which must be connected to the PSU to get power. Be sure to power on the miner only after all the 10 PCIe connectors are connected to a power supply.
Specification of V9:
Parameters of ANTMINER V9 | ||
No. | Parameters | Value |
1 | Product model | V9 |
2 | Hash chip type | BM1580 |
3 | Total quantity of hash chips | 135 PCS |
4 | Total quantity of hash boards | 3 PCS |
5 | Total hash rate | 4TH/s ± 5% |
6 | DC voltage input | 11.60~13.00 V |
7 | DC current input @12V DC | 79.59 A +10% |
8 | DC Power @12V DC input | 955 W +10% |
9 | 220VAC Power @25℃ ,93% conversion efficiency of APW3 | 1027 W +10% |
10 | 220VAC Power efficiency @25℃,93% conversion efficiency of APW3 | 253mJ/GH+10% |
11 | Weight(without package) | 3.05 kg |
12 | Operation temperature | 0-40 ℃ |
13 | Storage temperature | -40-85 ℃ |
14 | Operation humidity | 5%RH-95%RH, prevent condensation |
15 | Noise | 76 dB |
16 | Networking connection mode | Ethernet Cable |
17 | Power connection mode | All three PCI-E ports are required to power the board. You can use one PSU to power multiple boards, but do not attempt to power one board with two PSUs.We suggest to prevent the control board to be powered up before hash boards be powered up. |
18 | Size(Length*Width*Hight,without package) | 301mm*123mm*155mm |
Specification of APW3++
Overview:
1. The power cord is not included, please find one with at least 10A from your local market.
2. The APW3++ can deliver a maximum power of only 1200W if it is connected to a 110V mains power supply. To obtain the rated power of 1600W, the APW3++ must be connected to a 220-240V mains power supply. Please check the mains power supply that is the standard in your region before ordering.
Output:
1.DC Voltage:12.15V
2.Rated Current(220V input):133A
3.Rated Current(110V input):100A
4.Rated Power(220V input):1600W
5.Rated Power(110V input):1200W
4.Ripple & Noise:<1%
5.Voltage Regulation:<2%
6.Source Regulation:<1%
7.Load Regulation:<1%
8.Setup, Rise Time:<2S
9.Power off Protection Trip Time:>9mS
10.Interface Type:5 pairs of 6 pin PCI-E connectors (i.e. 10 connectors)
11.Noise Level:<43DB
Input:
1.Voltage Range:100-240V AC
2.Starting Voltage:95-105V AC
3.Frequency Range:47-63Hz
4.Power Factor:>0.95 (full load)
5.Leakage Current:<1.5mA (220V 50Hz)
Protection:
1.Low-voltage Input:80-89V AC
2.Output Short Circuit:Yes
3.Output Overcurrent:134-185A max.
4.Overheat Protection:Yes
Environment Conditions:
1.Operating Temperature:-20°C - 50°C
2.Operating Humidity:20% - 90% relative humidity (non-condensing)
Structure
Dimensions:220mm*108mm*62mm
Cooling Fan:Forced-air cooling
Note:This product does not contain 220V power cable!
BITMAIN Antminer V9 4TH/s ASIC Miner With APW3++ PSU
- Brands Bitmain
- Product Code: V9
- Availability: In Stock
- $315.02
-
$99.97
- Ex Tax: $99.97